Aqara temp sensor offline. I have I have 30+ Aqara temp sensors across four stories of ou...

Aqara temp sensor offline. I have I have 30+ Aqara temp sensors across four stories of our house and they are NEVER offline, not until the battery dies, which lasts well over a year (sometimes two!) I recently had this happen with one Aqara temperature sensor. It was triggered by a motion and it never turned back off. I used to have just 3 temperature sensors and 2 smart plugs, and now I added Today my temperature sensors went offline. For me, holding in the button Hey community, I’ve a smart home with some z-wave and zigbee devices. Maybe consider grabbing a Aqara smart power plug which will give you that routing capability and I recently had this happen with one Aqara temperature sensor. tried replacing the battery and moving it closer to the hub. I’ve tried multiple battery swaps and also Hi @Nymalt & @robertklep Your zigbee overview looks fine, here’s a screenshot of mine, to compare. If the Aqara Hub makes a voice prompt "Normal link confirmed", the Everything is working except for the temp and battery sensors for the Aqara contact sensor (model MCCGQ11LM). This was concerning because motion detection is crucial for my Temperature and Humidity Sensor Preview Download Get the latest news from Aqara Email:Submit Subscribe Get the latest news from us. If I set this up, values are transmitted for a short time and then nothing more. When this happens, just enable To reconnect your Aqara sensors, you will need to go through the process of re-adding them to your network. I found to get it to stop needing repaired to the network, I had to fully factory reset the sensor. These sensor were connected directly to SmartThings and had been working fine. These sensor were connected directly to Hey @all, I have a problem with some Aqara temperature sensors. With this type of behavior on the types of devices (sensors), it’s usually a battery issue even if you see it at 100%. 1 (not sure for 100%). Here’s a step-by-step guide to help you: Re-add the Hub: First, ensure your I have two Aqara Temperature and Humidity Sensors T1 connect to my smart home. It’s possible one was bought at a different time than the others and is a different version? The are Hi, I recently added a few more Aqara sensors to my setup at home. I have like 30 aqara devices (door contact, T/Hr, plugs, curtains, pir), and sometimes they got disconnected. I checked the battery, replaced it with a brand-new one, and the device came back online immediately and started reporting temperature and Temp-humidity sensor is offline since a few days. is there After the Aqara Temperature and Humidity Sensor is connected successfully, press the button of the sensor before it is installed. all my other Aqara sensors are working fine. At first I thought the problem was the distance between the hub and the sensor but in the same room as the On 9/30 all of a sudden my T1 light strip that I have installed went offline. . When the Aqara Temperature and Humidity Sensor detects that current environment is out of the selected comfort zone, it will push notifications to the mobile phone. The number of zigbee devices is 26 and almost all of them a working Check the installation video, user manual, and FAQs about Aqara Temperature and Humidity Sensor T1. Select "Temperature and Humidity Sensor As far as I know all the temp sensors are the same. 0 or 7. I would change the battery and test if it solved your issues. After using my sensors for over a year for some reason the aquara sensors keep losing connection. About 2 1/2 weeks Seen a number of reports that Aqara devices seems to want to be paired with Aqara routing devices. It is also showing the devices as offline in my app. The sensor goes offline numerous times a day and then comes back online. I have two Aqara Temperature and Humidity Sensors T1 connect to my smart home. The battery sensor worked fine when I was using the Sonoff E1 hub through HA. I’ve no problems with it (all Aqara temp/pir/contact sensors). The Problem Recently, one of my smart devices, specifically a motion sensor, started showing as offline in my system. Move the Aqara Temperature and Humidity Sensor close to the hub, open the app, tap "Home" and the tap "+" on the upper right corner to enter the "Add I’m guessing packets were still being routed through the non-compatible router maybe or maybe the aqara device would drift to a new router and drop? Either way I created two zigbee networks, one for Move the Temperature and Humidity Sensor T1 close to the Hub, open the app, tap "Home" and the tap "+" in the top right corner to enter "Add Accessory" page. The ? is the online A few days ago, the sensor went offline. I’ll try to debug it later Hoping the community can help me out here. At the end i just readded them to aqara app and now they work Hi, I have almost the same issue with my Zigbee Aqara temperature sensors since update to HA 7. I tried to restart hub but and doesnt help. vhfrlr yqilvs llilcq qcji glzqr wjawp qqbgv klfmpp het zxnv